SN46X8 SmartWare SWR 6.X Sample configuration SmartNode connected as
trunk gateway between a SIP network and PBX with 4 S0 port.
Copy and paste the below config in to a text editor.
Replace all the values as described on the lines starting with a #
T...
ENFORCE THE TRANSPARENT CODEC FOR ISDN UD-64 CALLS:
Incoming ISDN calls will be split into two call-router paths to
enforce transparent codec for ISDN unrestricted digital calls.
Note that the VOIP-DATA interface has no route into the call-router,
it o...
The DHCP client options, supported in SmartWare are:
DHCP Option
Name
Description
1
Subnet Mask
Specifies the clients subnet mask
3
Router
Specifies a list of routers for the clients subnet
6
Domain Name Se...
SN46XX SIP to ISDN Trunk Gateway configuration without SIP
registration. The ISDN PSTN may be connected to Port BRI 0/0 to 0/X.
Copy the content below this introduction and save it to a text file
for future upload to the SmartNode.
#---------------------...
Firmware file for use in redboot mode. NOT for SN45x2
The reason why the ACK for the 200 Ok from the SmartNode in some cases
is not accepted, is due to an invalid branch ID in the via header.
Based on the description in RFC 3261, the branch ID for a 2xx
response has to be different than in the former messag...
There are two possibilities:
1. Set the ISDN Presentation Indicator (PI) to restricted:
172.16.40.125(ctx-cs)[switch]#mapping-table pi to pi MT-PI-TEST
172.16.40.125(map-tab)[MT-PI-T~]#map default to restricted
2. Delete the Calling-Party Nummer usin...
ISDN LAYER 1 STATES
ISDN-PORT NETWORK MODE (NT1):
State G1 = NT1 DEACTIVATED
State G2 = NT1 PENDING ACTIVATION
State G3 = NT1 ACTIVATED AND WORKING
State G4 = DEACTIVATION REQUEST RECEIVED
ISDN-PORT USER MODE (TE)
State F1 = TE INACTIVE, NO POW...
The dial tone generated by a PSTN connection or a PBX can be extended
over the Internet or an Intranet by using a pair of Smartnode 452x
units or a Smartnode 452x and a Smartlink 402x unit. This FAQ
describes how to perform dial tone extension using a Sma...
Call-Routing tables offer two possibilities to terminate overlap
dialed numbers.
1. A dialling timeout
2. A special termination caracter like # or *
The timout and the caracter can be configured as follows:
172.16.40.125>enable
172.16.40.125#configu...
On the SmartNodes (SN-DTA/4V, 4110, 4120/4V, 4520, 463X, 465X 4830,
491X, 492X, 493X, IC-4FXS) is not possible to use two low-bit-rate
codecs at the same time per device. Thus you must choose to use either
G.723 or G.729 system wide. G.711 is always suppo...
CODEC
NET BANDWIDTH PER CALL (KBPS)
USED BANDWIDTH PER CALL (KBPS)
MIN. COMPRESSION DELAY (MS)
USAGE
G.711 a-law
64
96
10
Uncompressed, best voice quality, European audio-digitizing
G.711 u-law
64
96
10
Uncompressed, best voice quality, Am...
When using H.323 FastConnect (which is usually the case) together with
overlap dialing the voice codec is sometimes not known to the B-side
SmartNode in the route lookup. The configuration fragment below
exemplifies how to configure a SmartNode such that ...
The selection of a specific codec is somewhat tricky with the H.323
protocol. In SmartWare a specific codec can be entered at 2 different
locations:
a. in the h323 gateway configuration
b. in the h323 interface configurationThe following example
exemplifi...
THIS FAQ SHOWS A BASIC DESCRIPTION ON HOW TO CONFIGURE A SMARTNODE
COMMUNICATING WITH A SNMP-SERVER. FOR THOSE WHO ALREADY KNOW HOW TO
CONFIGURE THE SMARTNODE, PLEASE REFER TO CHAPTER 2 CONTAINING THE MOST
USED OID AND AS WELL TEMPLATES FOR CACTI.
* CH...
Debugging QoS is different from any other debug commands. It is a two
step process. You must be in configuration mode.
1) Go into your service policy and specify "debug queue statistics
detail 7"
2) Then do a show command: "show service-policy interface...
Debugging VPNs and ACLs is a bit different than using the other debug
commands. It is a two step process to enable ACL debugging. You must
first be in configuration mode.
1) Go into "context ip" and then into the ethernet interface and type
the following...
Multifrequency Compelled (MFC) Signaling was originally introduced by
the European Telecommunication Standards Institute (ETSI). Later, it
has been defined by the International Telecommunication Union (ITU) as
Signaling System R2 in the standards Q.400 - ...
The profile Argentina may be used when the carrier is Telefonica at
Colombia, here is an example to do it by telnet:
SN>enable
SN(cfg)#configure
SN(cfg)#profile r2 default
SN(pf-r2)[default]#load argentina
1. Open a telnet session using the command line interface of Windows.
Command: telnet "SN-ip-address|SN-hostname".
2. After opening the tool, open the properties of telnet and check the
quick edit mode check box. Then change to layout tab and set the
he...
Hold down the reset button while you power cycle the unit and make
sure you hold it down for at least 10 seconds. Connect a PC to the WAN
port of the SN4554. You will have to set your PC statically to an IP
address on the same subnet (172.16.40.2 255.255....
The following could be the issue in case a configured tone in a call
progress tone profile is not played as it is set.
In total 13 different tones, a combination of frequency and volume,
can be stored in the SmartNode tone database. This includes as well...
The internal timer configuration command is only able to execute
commands that produce an immediate result. Some commands that execute
asynchronously cannot be executed by the timer. The following commands
(among others) cannot be executed by the timer:
...
DAYLIGHT SAVINGS ON SMARTNODE
* On the SmartNode [http://patton.com/twiki/bin/view/Main/SmartNode]
a timezone and a DST rule can be defined. For Daylight Saving Purposes
there can be Timers defined which adjust the Timezone Offset according
to the Day...
The WAN access speed is expected to be large enough to handle all
voice connections on the SmartNode. Moreover the voice portion of the
used access bandwidth is expected to be small with respect to total
bandwidth. For example a DSL access with 700kbps or...
In ISDN supplementary service can be invoked by means of thekeypad
protocol. A service can be invoked with the digitsequence *21#. The
phone sends these digits as information element 'Keypad Facility' and
not as informationelement 'called party number'. A...
Yes.
Generally, DTMF can always be transported either out-of-band or
in-band. in-band provides the most accurate timing reproduction of
DTMF, but it is not suitable when a compressing codec is used, e.g.
G.729 or G.723.
In these cases, out-of-band has to...
The SmartNode is a router as per RFC1812/RFC1256 and thus sends "ICMP
Router Discovery" messages to the subnet to which it is attached. Some
MS Windows versions react to such messages and automatically adjust
their routing tables. In order to avoid such u...
Up to 3 different gatekeeper IP addresses can be configured on a
SmartNode.If the SmartNode is unregistered from the gatekeeper by
means of an URQ message, after sending a UCF message the SmartNode
tries (instantaneously) up to 3 times (every 20s) with a...
When using NAPT on a SmartNode there is one global IP interface (with
the public IP address) and one local IP interface (with the private IP
address). The H.323 gateway must be bound to one of the interfaces
since it needs to know on which interface it mu...
CONFIGURATION DESCRIPTION:
This example shows which mapping tables are used to get the "clip no
screening" working towards the ISDN PSTN network.
The call comes in on isdn interface 01 and passes the complex function
contatining 3 mapping tables. In t...
CONFIGURATION DESCRIPTION
It is possible to store call logs with quality information in the
local aaa data sink. To do so, a service aaa is needed where the calls
are routed through. Create a profile aaa with the method local. Then
create a service aaa ...
CONFIGURATION DESCRIPTION
The service 'priority' can automatically free resources if a high
priority call needs to be established while no resources are
available. The service 'priority' can have multiple ports. You can
assign a priority level for each ...
CONFIGURATION DESCRIPTION Allows you to pick up Phone 0 and ring all
other 7 ohones at the same time. Then once one of the other 7 phones
is answered the call is connected and the other phones cease ringing.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
co...
CONFIGURATION DESCRIPTION
The call-router 'limiter' service limit offers with a flexible
technique to limit the maximum number of concurrent calls. It also
limits the call-setup rate within a system. Calls exceeding the
defined limits can either be simp...
CONFIGURATION DESCRIPTION
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
#-----------------------------------------------------------------#
# #
# SMARTWARE 5.X #
# #
# ENHANCEMENT for CALL-DETAIL-RECORDS over RADIUS #
# #
# This config example is an enhanc...
CONFIGURATION DESCRIPTION The SmartNode sends a CDR message if a
incoming or outgoing Call-Setup passes the SIP-Interface.
You may define and configure a independent CDR-services-element for
each call-routing-leg.
COMMANDE SEQUENCE TO COPY, EDIT AND PAS...
CONFIGURATION DESCRIPTION
Incoming SIP call rings four phones simultaneously.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
#-----------------------------------------------------------------#
# #
# SMARTWARE 5.X #
# #
# Incoming SIP call rings 4 Analogu...
CONFIGURATION DESCRIPTION
Inbound SIP call hunting across 4 FXS interfaces
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
#-----------------------------------------------------------------#
# #
# SMARTWARE 5.X #
# #
# Inbound SIP call hunting across 4 FXS...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide
second-dial-tone service. Once a user connects to a SmartNode FXO
port, SmartNode will generate and deliver a second dialtone to the
user. The routing-table RT_CDPN decide...
CONFIGURATION DESCRIPTION
ENFORCE THE TRANSPARENT CODEC FOR ISDN UD-64 CALLS:
Incoming ISDN calls will be split into two call-router paths to
enforce transparent codec for ISDN unrestricted digital calls.
Note that the VOIP-DATA interface has no rout...
CONFIGURATION DESCRIPTION
SmartNode used as gateway between a SIP network and a phone, connected
to port 0/1. The Port 0/0 is configured as user and can be used as
fallback to a PSTN. Emercency calls will be routed to PSTN instead of
VOIP.
COMMAND SEQ...
CONFIGURATION DESCRIPTION
SN46X8 SMARTWARE 5.X Sample configuration SmartNode connected as trunk
gateway between a SIP network and PBX with 4 S0 port. The Port S0 slot
0 port 0 is configured as fallback and sync-port. It is configured in
the user mode a...
CONFIGURATION DESCRIPTION
The example shows you, how to bundle multiple PPP lines into one,
using one subscriber. You may add additional lines in the same way.
COMMAND SEQUENCE TO COPY, PASTE AND EDIT
context ip router
interface IF_MLPPP
ipaddres...
CONFIGURATION DESCRIPTION
The example shows you how to bundle multiple PPP lines into one, using
two subscribers. You may add additional lines and subscribers in the
same way.
IMPORTANT: Both subscribers needs the same mulitlink settings
COMMAND SE...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to operate as a DHCP client by pointing a SmartNode IP-interface to a
DHCP server on the directly connected LAN. As a DHCP client, upon
power-up the SmartNode can automatically retreiv...
CONFIGURATION DESCRIPTION
The command sequence below enables static-IP-addressing by assigning a
fixed IP address, netmask, and default gateway address to a SmartNode
IP interface.
To complete this configuration you will need the following
information:...
CONFIGURATION DESCRIPTION
Sometimes you need to specify default routes for traffic in specific
traffic-classes. SmartNodes have three built-in traffic-classes
(expandable in configuration) which are used for Quality-of-Service
purposes.
For each traff...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to operate as a DHCP
server. In networks where the SmartNode is the Internet Gateway
Router, this configuration is the best way to provide user devices
with Internet access. Once ena...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to support dynamic
service via DynDNS (i.e. http://www.dyndns.org). If your IP address
changes more often than once every 28 days you should use this Service
Dynamic configuration. I...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to support static service
via DynDNS (i.e. http://www.dyndns.org). If your IP address changes
less often than every 28 days, you should use this Service-Static
configuration. If your...
CONFIGURATION DESCRIPTION This example includes a basic configuration
for the SmartNode 4638 as a PSTN gateway in combination with a GFI
Faxmaker. This example can be used for other SmartNodes too. The only
thing which needs to be adjusted, are the ports ...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode 4112 as
a PSTN gateway in combination with a GFI Faxmaker.
This example can be used for other SmartNodes too. The only thing
which needs to be adjusted, are the po...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode
SN49XX/ISDN for use as a PRI gateway in combination with a Cisco Call
Manager. The configuration contains variables in brackets <>. Please
Replace the variables incl...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode
SN49XX/ISDN to be used use as a PRI gateway in combination with a
Cisco Call Manager. The configuration contains variables in brackets
<>. Please Replace the variabl...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode
SN49XX/ISDN to be used as a PRI gateway in combination with two Cisco
Call Manager (Primary and secondary). The configuration contains
variables in brackets <>. Plea...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode SN5XXX
to be used as a Session Border Controller in combination with two
Cisco Call Manager (Primary and secondary). The configuration contains
variables in brackets...
CONFIGURATION DESCRIPTION Configuration for SN4112 for use with Avaya
Open Office.
============================================
This example includes a basic configuration for the SmartNode
SN4112/JS for use as an analog Terminal gateway (ATA for Fax and
...
An ISDN S-Bus can provide up to 8W of 40V DC power. Many ISDN Phones
draw their operating power from the ISDN S-Bus. This is usually not
the case for PBX systems which are typically local mains powered.
Check the technical specifications of your ISDN term...
CONFIGURATION DESCRIPTION
In some cases, more FXS, FXO or BRI ports are needed as available on
one SmartNode for certain applications. This conifg example shows, how
to stack two or more SmartNodes, achieving more channels / ports.
The idea is to let ...
The analog facsimile attached to a terminal adapter (which in turn is
connected to a S0 interface of the SmartNode) does not send the called
party number.
Analog faxes wait for a dial tone prior to send the called party
number. Despite this the terminal...
If you want route a multicast stream, you need to configure this on
the ethernet interfaces.
There are two commands, one for the sending interface (to the
clients) and the other for the receiving interface (eg. from the WAN).
interface IF_IP_WAN
ipadd...
SmartWare is the embedded software running on the SmartNodes.
SmartWare offers a number of feature options such as QSIG, VPN and IP
forwarding.
Up to SmartWare release 2.20 feature options had to be paid but where
not keyed. Starting with release 3.10 a ...
License Key installation is described in the Software Configuration
Guide 3.10 in the Chapter "Basic System Management" section "Managing
Feature License Keys".
To install the licenses, simply copy the install command and license
key ("install license 0...
There are two possible reasons for that. 1. You may be trying to
install the wrong key. Make sure the keys you are installing match the
serial number of the SmartNode. 2. You may have an early access build
of SmartWare release 3.00 or 3.10. Please upgrade...
Some SmartNode 4000 series units have a serial number notation using
colons ":" that do not work with the early access builds of Release
3.10. Upgrade first to the commercial version of 3.10 and the install
the license keys.
IP forwarding will be disabled. That means you can still access the
SmartNode on all IP interfaces but the SmartNode is not routing IP
packets between interfaces. Also if you have been using other feature
options such as VPN or QSIG these functions will b...
H.323 is a non-well behaving protocol in that it signals transport
ports (RTP ports) inband in IP packets. When using NAPT (Network
Address and Port Translation) this poses a problem since the ports are
used by NAPT for address mapping. Thus H.323 does us...
Yes, If you are on a private network, your firewall or NAT (Network
Address Translation) router must be "H.323 aware" or you'll need a SIP
proxy if you are using SIP. To help determine if your LAN uses NAT,
you can use a web browser and go to the followin...
Usually RTP streams are processed on SmartNode before they reach the
ACL (Access Control List). This is due to add as less as possible
processing delay to it. But in some scenarios the RTP traffic may be
restricted using an ACL. For such cases the followi...
In some cases you may want to create multiple SIP gateways to
subscribe to multiple SIP Telephony Services at the same time, or to
seperate LAN SIP calls from Global/Internet SIP calls.
In order to bind multiple SIP gateways to the same IP interface th...
The only Siemens Qsig Protocol, which is interoperable with the
SmartNode products is ISO-QSIG.
You must choose as QSIG version ISO-QSIG.
All other Siemens Qsig versions show restrictions in the supported
supplementary services, such as the caller n...
By default the SmartNode handles hook FLASH events by itself, i.e. a
call is held locally, and if it is transferred, it is looped locally
as well.
If you want to transmit the DTMF towards the far end, you must
disable the additional servivces on the fxs...
A common application is to accept calls from a PSTN on an FXO port and
then ring a telephone connected to a FXS port. In order to send a
FLASH out the FXO port to the PSTN, you must disable all supplementary
calling features on the FXS interface. For exam...
SmartWare FLASH Codes
-FLASH 0 - keep current, reject incoming
-FLASH 1 - drop current, accept incoming
-FLASH 2 - hold current, accept incoming
To toggle between the active and the held call, press flash-hook,
followed by the "2" key.
Additional...
If the message OUT OF MEMORY appears, you may do the following
1. Store the current running-config in a separate file
2. copy the config which is linked below, to the startup-config in
the SmartNode and reload it. Be sure about the ip addresses. If th...
CONFIGURATION DESCRITIPON
Configuration for SN4638 for use with OCS. A more detailed explanation
you will find on the following link.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
#----------------------------------------------------------------#
# #
# ...
If a firmware update fails the SmartNode will enter the bootloader
mode. You can access the SmartNode ONLY with ethernet on the last
known ip-address. The username is "admin" and the password "inalp".
After successful login you can download the new fir...
Each SmartNode is equipped with a bootloader application. If an
upgrade fails and no valid firmware is available on the system the
SmartNode will start in this bootloader mode. The bootloader will
allow you to install a new firmware.
Please refer to the ...
We recommed two good TFTP Servers: First the Solar Winds TFTP Server
is found on the SmartWare CD. You can also download it from the
SolarWinds web site
[http://support.solarwinds.net/updates/New-customerFree.cfm]. Use
SolarWinds version 3.0.9 or higher. ...
Yes, Release 3.10 adds SIP and a lot of new session router features.
The configuration must be converted. An easy to use on-line tool and
instructions can be found at Smart Convert
[http://patton.com/support/smartconvert]
Quote: DES Key Parity from Phil Harding
[http://blogs.wdevs.com/philharding/archive/2005/09/08/10490.aspx]
-------------------------
A single DES key is 64 bits (8 bytes) long, however the actual key
material used by the DES algorithm amounts to only 56...
Yes, with SmartWare software releases dated 3/1/06 and later.
For earlier relases, VoIP calls terminated on the SmartNode route the
RTP outside the VPN tunnel.
A VPN feature license has to be installed for this feature to work.
The SmartNode does not have a preset limitation of VPN tunnels.
The number of VPN tunnels that you are able to create is only limited
to the amount of available RAM. In practice the SmartNode will support
a minimum of 10 VPN tunnels but also 100 tunnels...
T-Online uses the username in three steps.
a) 12 digits connect-number
b) 9 to 12 digits T-Online-number (if <12 digits add a hash (#) in
front)
c) user-suffix is always 0001 folowing by @tonline.de
The username is therefore:
aaaaaaaaaaaabbbbbbbbbb...
CONFIGURATION DESCRIPTION
!Additional license required for Dial-up!
This example configuration can be used as a backup solution, in case a
specific host in a specific network is not available anymore. In this
case an ISDN Dial-up connection will be se...
CONFIGURATION DESCRIPTION
The following will take calls in the FXO port, and send it out sip. It
will also take calls in SIP and then hunt across all the FXO ports to
find a open port This config also contains the USA tonesets, you can
change that as ne...
This is a configuration template for an SN-DTA with registration to a
SIP Telephony provider.
With this config all national and international calls as well as the
local calls will be routed to the SIP provider.
All emergency and special Service Number...
CONFIGURATION DESCRIPTION
Generic Altigen H.323 SOHO Router Config
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
cli version 3.00
banner "My Altigen Config"
dns-client enabled
dns-client cache 30
dns-relay
webserver port 80 language en
snmp community pu...
CONFIGURATION DESCRIPTION SN4528 R5.X -should also load in any SN452x
- ignore errors for missing ports
- uncommment lines in SVC-DG-BROADVOICE for ports used)
- Replace with telephone number
- Replace ‹PASSWORD› with Password
- Replace ‹SMARTNO...
CONFIGURATION DESCRIPTION
SmartNode used as a PSTN/ISDN and terminal gateway in a Media-Streams
e-Phone enviroment.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
#----------------------------------------------------------------#
# #
# SN1x00 #
# R3.10 #...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to operate as an H.323
gateway for registration with a GateKeeper.
NOTE: You must replace. . . xxx.xxx.xxx.xxx . . . with your
GateKeeper's IP address.
COMMANDE SEQUENCE TO COPY,...
CONFIGURATION DESCRIPTION
SN46XX SIP to ISDN Trunk Gateway configuration without SIP
registration. The ISDN PSTN may be connected to Port BRI 0/0 to 0/X.
Copy the content below this introduction and save it to a text file
for future upload to the SmartN...
CONFIGURATION DESCRIPTION
PSTN trunk gateway for Aserisk IP-PBX application
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
#----------------------------------------------------------------#
# #
# Patton SmartNode SN46XX #
# SWR5.X #
# #
# PSTN trunk gatew...
CONFIGURATION DESCRIPTION
In case you need to put the SmartNode in front of a firewall you can
forward every ip-packet which is not handled by SmartNode to the
firewall.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
profile napt
dmz-host ...
CONFIGURATION DESCRIPTION
The command sequence below will create a NAPT profile and apply it to
the SmartNode's global IP Interface. A home office with the following
characteristics will typically use Dynamic NAPT configuration:
- a single global IP a...
CONFIGURATION DESCRIPTION
The command sequence below will create a NAPT profile with port
mappings and apply it to the SmartNode's global IP Interface. This
configuration allows SmartNode to forward incoming IP connections on
specified ports of the glob...
CONFIGURATION DESCRIPTION
The command sequence below will create a NAT profile with static
address mappings and apply it to an IP interface on the SmartNode.
This configuration allows SmartNode to translate IP adresses
one-to-one for incoming and outgoi...
CONFIGURATION DESCRIPTION
The configuration example below shows how to configure 802.1q Vlan's
on a SmartNode Ethernet port.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
context ip
interface IF_IP_VLAN1
ipaddress 10.0.0.1 255.255.255.0
interfa...
CONFIGURATION DESCRIPTION
Port and context ip configuration for a PPPoE connection over the
SmartNodes G.SHDSL.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
context ip router
interface IF_WAN
ipaddress unnumbered
mtu 1492
point-to-point
use profil...
CONFIGURATION DESCRIPTION
Port and context ip configuration for a ADSL PPPOEOA (POINT TO POINT
OVER ETHERNET OVER ATM) link over a SmartNode VoIP-Gateway.
This example is for SmartNode models using the ADSL interface which is
indicated by "/A" in the p...
CONFIGURATION DESCRIPTION
FXS Port configuration. To be used in the US. For Europe usage, just
replace "bell" with "etsi".
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
port fxs 0 0
caller-id format bell
use profile fxs us
encapsulation cc-fxs
bind i...
CONFIGURATION DESCRIPTION
FXO Port configuration. To be used in the US. For Europe usage, just
replace "bell" with "etsi".
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
port fxo 0 0
use profile fxo us
caller-id format bell
encapsulation cc-fxo
bind i...
CONFIGURATION DESCRIPTION
SN4960 E1 Configuration with DSS1 signaling protocol
Sample Configuration;
port 0 0 may be connected to a PSTN line
port 0 1 may be connected to a ISDN E1 PBX
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
system
clock-sou...
CONFIGURATION DESCRIPTION
Port and context ip configuration for a Frame-Relay connection over a
V.35 or X21 serial link. The transmit-data-on-edge setting depends on
the remote modem device
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
context ip
inter...
CONFIGURATION DESCRIPTION ISDN T1 port configuration. To be connected
to a PBX.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
port t1 0 0
clock master
encapsulation q921
q921
protocol pp
uni-side net
encapsulation q931
q931
protocol ni2
uni-side ...
CONFIGURATION DESCRIPTION
2300/2400 T1 Card in Slot 3 0 User-Side DD
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
configure
system
clock-source internal
exit
context cs switch
routing-table called-e164 TAB-FROM-SWITCH
interface isdn IF-SWITCH
rou...
CONFIGURATION DESCRIPTION
Port and context ip configuration for a PPP connection over a V.35 or
X21 serial link. The transmit-data-on-edge setting depends on the
remote modem device.
COMMAND SEQUENCE TO COPY, EDIT AND PATE
context ip
interface IF_...
CONFIGURATION DESCRIPTION
A standard PPPoE configuration including authentication.
# Replace ‹account› and ‹password›
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
configure
profile napt PF_NAPT_WAN
port ethernet 0 0
encapulation pppoe
context ip
i...
CONFIGURATION DESCRIPTION This configuration checks 2 minutes after
boot up for new firmware and if available downloads and istalls it.
Furthermore the server will be checked every minute for new firmware.
Furthermore SmartNode checks 30 minutes after bo...
CONFIGURATION DESCRIPTION
Quality-of-Service needs to be configured carefully. Especially the
rate-limit values needs to be exact as this is the base for
prioritizing the data/voice traffic.
All the values in brackets <> needs to be replaced. Please h...
CONFIGURATION DESCRIPTION
The firmware 5.X supports the registrar function what allows SmartNode
to accept registration from any kind of SIP-clients (telephones,
soft-clients).
The example configuration shows how such an so called identity needs
to be ...
CONFIGURATION DESCRIPTION
This configuration examples may be used in applications, where the
gateway has to use the SIP-Username, e.g. root calling number, for
registration and outbound authentication but the content of the
SIP-From-Header may change; e...
CONFIGURATION DESCRIPTION This configuration shows an example for how
to route calls beetwen an ISDN and SIP network including registration
on a SIP server using the new SIP gateway configuration architecture
within the SWR5.T software version.
COMMANDE...
CONFIGURATION DESCRIPTION
CONFIGURATION IS BASED ON RETIRED SOFTWARE RELEASE!
Below you will find different configuration examples for a SIP-Gateway
configurations. The type of the proxy does not matter as the
configuration is the same. Please note th...
CONFIGURATION DESCRIPTION A Simple Asterisk Registration into PBX T1
on Port 0 0
#
# Replace ‹0.0.0.0› with IP address or dns name of the registrar,
e.g. 192.168.1.1
# Replace ‹XXX› with account, e.g., 1234
# Replace ‹YYY› with account password, e.g., mys...
CONFIGURATION DESCRIPTION A Simple Asterisk Registration into PBX E1
on Port 0 0
#
# Replace ‹0.0.0.0› with IP address or dns name of the registrar,
e.g. 192.168.1.1
# Replace ‹XXX› with account, e.g., 1234
# Replace ‹YYY› with account password, e.g., my...
CONFIGURATION DESCRIPTION Configuration for a Pingtel / sipX PBX
-US Dial Tones
-SN45xx (firmware 5.X) based
-Replace all <>-variables with appropriate values
CONFIGURATION TO COPY, EDIT AND PASTE
profile call-progress-tone US_Dialtone
play 1 0 350 -...
CONFIGURATION DESCRIPTION Smartware version R5.X not older than
2010-07-15 Use these two commands to achieve that the SmartNode
automatically performs the daylight saving change. This example is for
countries with default offset +01:00 and daylight saving...
CONFIGURATION DESCRIPTION
SNTP configuration recomendation for Japan. This configuration uses a
combination of one DNS name in Japan and one IP address in Japan. DNS
server must work work for DNS to be resolved. SNTP should continue to
work if DNS break...
CONFIGURATION DESCRIPTION SNTP configuration recomendation for Mexico.
This configuration uses a combination of one DNS name in Mexico and
one IP address in USA. DNS server must work work for DNS to be
resolved. SNTP should continue to work if DNS breaks ...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in
Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below
enables SmartNode to provide the standard Norway1 style tone set for
dial-tones and call-progress tones.
COMMAND...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in
Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below
enables SmartNode to provide the standard Norway1 style tone set for
dial-tones and call-progress tones.
COMMAND...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in
Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below
enables SmartNode to provide the standard Norway1 style tone set for
dial-tones and call-progress tones.
COMMAND...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Czech Republic style tone set for dial-tones
and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone CZ_Dialtone
play ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard France style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone FR_Dialtone
play 5000 440...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Hungary-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone HUN_Dialtone
play 5000 4...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Italy-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone IT_Dialtone
play 200 425 -...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Mexico style tone set for dial-tones and
call-progress tones.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone MX_Dialtone
play 1 200 4...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Netherlands style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone NL_Dialtone
play 1 2...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard New Zealand-style tone set for dial-tones and
call-progress tones
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone NZ_Dialtone
play 1 50...
CONFIGURATION DESCRIPTION There are Two distinct tones sets used in
Norway. Norway1 and Norway2. The command sequence below enables
SmartNode to provide the standard Norway1 style tone set for
dial-tones and call-progress tones.
COMMANDE SEQUENCE TO COP...
CONFIGURATION DESCRIPTION There are Two distinct tones sets used in
Norway. Norway1 and Norway2 The command sequence below enables
SmartNode to provide the standard Norway2 style tone set for
dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY,...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Poland-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone POL_Dialtone
play 5000 42...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Russia-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone RUS_Dialtone
play 5000 42...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Slovenia-style tone set for dial-tones and
call-progress tones.
COMMANDE SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone SLVN_Dialtone
play 700...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard South Africa-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone ZA_Dialtone
play 1 ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Spain style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone ES_Dialtone
play 1 200 425...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard Sri Lanka-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone LK_Dialtone
play 5000 ...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide the standard
Sweden-style tone set for dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone SE_DIAL
play 1 5000 425...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode
to provide the standard UK-style tone set for dial-tones and
call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone UK_Dialtone
play 1 5000 350 -1...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide the standard
USA-style tone set for dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
configure
system
profile call-progress-tone US_Dialtone...
The command sequence below defines a VPN Tunnel that uses AES-128 to
route traffic from Side #1 (192.168.1.0) to Side #2 (192.168.2.0).
NOTE:
-You must replace ‹X.X.X.X› in the template with the IP address
for Side #2.
-You must replace ‹MySharedKey...
CONFIGURATION DESCRIPTION
The command sequence below defines a VPN Tunnel that uses AES-128 to
route traffic from Side #2 (192.168.4.0) to Side #1 (192.168.1.0).
NOTE:
-You must replace ‹X.X.X.X› in the template with the IP address
for Side #2.
-You mu...
CONFIGURATION DESCRIPTION
The command sequence below defines a VPN Tunnel that uses DES to route
traffic from Side #1 (192.168.1.0) to Side #2 (192.168.2.0).
NOTE: You must replace X.X.X.X in the template with the IP address for
Side #2.
NOTE: You mus...
CONFIGURATION DESCRIPTION The command sequence below defines a VPN
Tunnel that uses DES to route traffic from Side #2 (192.168.2.0) to
Side #1 (192.168.1.0).
NOTE: You must replace X.X.X.X in the template with the IP address for
Side #1.
NOTE: You must ...
In some cases SIP calls are disconnected after 32 seconds.
This happens when the SmartNode involved is B side of the connection.
Looking at a debug log of such a call, it can be seen that several 200
OK and ACK messages are sent back and forth.
This is ...
This article contains a SmartNode voip profile configuration example
to be used together with a Hylafax software based on Asterisk. As well
a Hylafax /Asterisk configuration recommendation is included. Both the
SmartNode and Hylafax settings were successf...
The following configuration can be used to register with a Skype
Connect account.
#--------------------------------------------------------------- #
# #
# SN4634/5BIS/UI #
# R6.x #
# Autor: Thomas Tlapak #
# Date: 03.07.2012 #
# #
# Contact: support@pat...
1 INTRODUCTION
Security is in the today communication systems a key element
required to have a stable and reliable IT service. This includes not
only data security however also written and mutual communication.
Open VoIP networks are attackable us...
CONFIGURATION DESCRIPTION
The below SmartNode configuration template will help connect your
Cyber-Data IP Paging equipment to Microsoft Lync.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE IN THE FOLLOWING LINK
configuration example
[http://support.patton...
Basically all 4xxx SmartNode models are interoperable with Microsoft
Lync.
On the following link more details about configurations of both, the
Lync server and the SmartNode can be found.
Microsoft Lync and SmartNode
[http://www.patton.com/voip/appnot...
FXS GATEWAY IN COMBINATION WITH ASTERISK
This template can be used to register a fxs gateway with at Asterisk
PBX.
To enhance Lync with a legacy PSTN or an analogue terminal a Voice
over IP gateway is required. The SmartNode products line, Certified
for Lync by Microsoft, is the right choose for such a scenario.
A step by step configuration guide to configure the Sm...
If a firmware update fails the SmartNode will enter the u-boot mode.
Connect a computer to the console interface and restart the SmartNode.
You will see the Prompt "=>".
HOW TO FORCE THE SMARTNODE ENTERING THE BOOTLOADER/U-BOOT MODE
While connected wit...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide the standard
Japan-style tone set for dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
configure
system
profile call-progress-tone JP_Dialtone...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode
SN411X/FXS to be used as an FXS gateway in combination with a Cisco
Call Manager. The configuration contains variables in brackets <>.
Please Replace the variables i...
The information in this article applies to:
SWYXWARE 2011 R2
PATTON SMARTNODE (6.T BUILD SERIES 2012-07-18)
Within the Swyx Technology Partner Programme (TPP) the Patton
SmartNode (6.T Build Series 2012-07-18) was successfully tested
against a S...
Low bitrate codecs supported on Smartware are
G723 and G729
On some of the SmartNodes, only one low bitrate codec is supported at
the time, systemwide.
There the following setting is required to make the G729 codec work.
system
ic voice 0
low-bit...
profile call-progress-tone AIRTEL_LL_DTONE
play 1 40 401 -19 375 -23 modulated 50
--> 50 - default modulation
1) Open PuTTY. (download link:
http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe
[http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe])
2) Click 'Window' and set 'Lines of scrollback' to '9999999'
3) Enter in IP address of SmartNode and h...
This article describes how to configure a Patton SmartNode with
Voxbone International Inbound SIP Trunking service
[http://www.voxbone.com/], which provides Telephone numbers (DID) and
toll-free numbers in 50+ countries and 4000+ area codes
[http://www.vo...
CONFIGURATION DESCRIPTION
In cases where an ISP assigns to your SmartNode's WAN interface a
public IP address, and provides you as well with multiple public IP
addresses within the same subnet, all to be assigned to different
hosts/servers within your n...
For Ethernet port redundancy, the SmartNode / SmartWare action script
functionality will move the interface binding from one Ethernet port
to the other in case a failure on the Master Port appears. For the
master port supervision, an additional interface ...
To enable SmartNode to connect using ISAKMP VPN to a Cisco ASA here is
a template.
The goal of this configuration was to create a secure tunnel ( now
only for voice ) via VPN.
Topology:
- - =VPN= -
The network 10.100.1...
To configure a SmartWare SmartNode FXS Gateway within 3CX, please
visit the link below.
http://www.3cx.com/blog/voip-howto/patton-fxs-gateway-at/
To configure a Trinity SmartNode FXS Gateway within 3CX, please visit
the link below.
https://www.patton...
When your SmartNode is connected to a public network, it must be
properly configured in order to prevent it from unwanted attacks.
First of all make sure an ACL is configured and enabled in the
corresponding IP interface. In the ACL make sure that only ...
CONFIGURATION DESCRIPTION
This example includes a basic configuration for the SmartNode
SN4118/JS to be used as a FXS gateway in combination with two Cisco
Call Manager. The configuration contains variables in brackets <>.
Please Replace the variables i...
CONFIGURATION DESCRIPTION
Port and context ip configuration for a ADSL link over a SmartNode
VoIP-Gateway using PPPOA ENCAPSULATION.
This example is for SmartNode models using the ADSL interface which is
indicated by "/A" in the product SKU.
In case ...
Article covers configuration impact on 'service aaa' behaviour in case
RADIUS server stops responding to Accounting Requests. Tested against
SmartNode 4112 running SmartWare 6.5 and Freeradius server version
2.1.10.
Our goal was to pursue a solution in ...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide the Austria
420Hz style tone set for dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone AUT420_Dialtone
play 5000...
CONFIGURATION DESCRIPTION
The command sequence below enables SmartNode to provide the Austria
450Hz style tone set for dial-tones and call-progress tones.
COMMAND SEQUENCE TO COPY, EDIT AND PASTE
profile call-progress-tone AUT450_Dialtone
play 5000...
Whenever you are experiencing connectivity issue on the e1t1/ethernet
a great tool to test if the ports are working fine would be the
loopback cable.
A loopback cable redirects the output back into itself. This
effectively gives the network interface th...
Echo is commonly encountered on PSTN when analog lines are involved in
the conversation path. Patton SmartNodes have an integrated echo
canceller for that purpose. Because it works adaptively, only the echo
that really exists is cancelled. The best place ...
The following article is a comparison of the debugging commands found
in the Patton SmartNode VoIP Gateway products. Patton SmartNode's have
been running SmartWare since conception but Patton recently developed
and released a newer software platform calle...
One of the main reasons for this is that the SmartNode does not allow
for any "untrusted" host IP Addresses to pass through whenever the
"trust" command is configured in the SIP interface.
MANAGING TRUSTED HOSTS:
A list of trusted remote peers can be ...
By default, the SmartNode listens for both TCP and UDP traffic. In
order for the SmartNode to send SIP signaling using TCP, you will need
to configure the following:
location-service SER_LYNC
match-any-domain
identity-group default
call outbound
...
To import a SmartNode T1 Gateway xml template into 3CX, you will first
need to download the template from here
[http://patton.com/files/support/kb/Patton-T1.gw.zip]. Once you
download the file and extract the "Patton-T1.gw.xml" from the zip
file, you will...
Below are the default RTP port ranges in the Patton SmartNodes and
how to configure them per software platform.
SmartNodes running SmartWare:
RTP-PORT-RANGE 4864 5375
Configuration:
10.10.50.17>enable
10.10.50.17#configure
10.10.50.17(cfg)#con...
Certain carriers require that the Numbering Plan and Type of Number,
sent in the ISDN SETUP message, be National/isdn-telephony
(ISDNTelephony e.163,4). Unless configured otherwise, the SmartNode
will send this as UNKNOWN/UNKNOWN.
SETUP (DSS1 User)
[040...
The below screenshots shows how Mitel 3300 needs to be configured.
Below is the Smartnode configuration where
# Smartnode IP= 10.10.10.10
# Mitel Ip = 10.10.10.11
# SIP Account 8998
context ip router
interface eth0
ipaddress 10.10.10.10 255.255....
Patton SmartNodes have a very complex digit manipulation engine that
is highly configurable for most parameters within a call setup.
MAPPING TABLE:
* Selects the best matching entry
* Sets/Changes the value of the defined Information Element
* M...
A common problem when SmartNodes are unable to register with 3CX
happens to be caused by the auto-blacklist feature by 3CX. After a
number of failed registration attempts to 3CX, a device will be
blacklisted automatically, thus preventing registration and...
Patton has created new 8-32 FXS port templates that are available to
download and install into your 3CX Phone System. Just a few simple
steps and you will be configuring your SmartNode IPChannelBank devices
in no time at all.
SUPPORTED PRODUCTS:
SN4300...
Help Desk Software by Kayako