|
The information in this article applies to:
SwyxWare 2011 R2
Patton SmartNode (6.T Build Series 2012-07-18)
Within the Swyx Technology Partner Programme (TPP) the Patton SmartNode (6.T Build Series 2012-07-18) was successfully tested against a SwyxWare 2011R2 (QuickFix 3) and hereby reaches the certification level certified.
This KB article describes all mandatory configuration steps which are needed to assure a flawless operation between a Patton SmartNode and a SwyxWare 2011R2.
1. Certification test
The test was made between a Patton SmartNode 4635 and two SwyxWare20122R2 Quickfix3 in Master-Standby operation.
Patton SmartNode4635
Firmware: SmartWare 6.T Build Series 2012-07-18
SwyWare2011R2 QuickFix3
IpPbxSrv.exe v8.1.0.257
IpPbxGate.exe v8.1.0.84
LinkMgr.exe v8.1.0.83
PhoneMgr.exe v8.1.0.94
ConferenceMgr.exe v8.0.1.19
IpPbxFaxSrv.exe v8.1.0.113
IpPbxCDSService.exe v8.1.0.623
Endpoints:
SwyxIt 8.01.0678
SwyxPhone L615
SwyxSIPPhone S315
1.1 Executed tests
Incoming and outgoing calls with the above endpoints from and to PSTN / GSM
Signaling
CLIP
CLIR
CLIP No Screening
Long duration calls
Hold / Retrieve
Call toggeling
Transfer
Conferencing
Call forwarding internal/external
DTMF Signaling
T.38 negotiation and FAX transmission
All testcases were completed successfully.
2. Getting started
The following steps are necessary for a get started:
Preparation of SwyxWare, i.e. installation of the latest Quickfix, creation of a SIP gateway trunk und SwyxWare user; configuration of SwyxWare locations if necessary
Preparation of the Patton SmartNode
Adjustment and installation of the Patton SmartNode INI file
2.1. Preparation of SwyxWare
Make sure that at least Quickfix 3 or a more recent Customer Hotfix/Quickfix is installed for SwyxWare2011R2.
Using the configuration assistant, create a new SIP Gateway Trunk group within the SwyxWare. Select the Trunk Group Profile "SwyxConnect 6000" that fits to your environment.
Create a new SIP Gateway Trunk for the newly created SIP Gateway Trunk Group.
Configure "SIP-User-ID" and "SIP Username" with a value of your choice, use the same value for both items.
Configure the SIP password.
Configure the available range of external numbers.
Activate all codecs.
Configure the number of available channels.
Set the local NetBIOS name as "Computername".
Afterwards, open the properties of the newly created SIP Gateway Trunk.
In the tab "Encryption", set the encryption mode to "No Encryption".
2.2. Preparation of Patton SmartNode
Please update the firmware of the Patton SmartNode to SmartWare 6.T Build Series 2012-07-18 before adjusting the configuration. The latest firmaware can be found at http://www.patton.com/support/upgrades/index.asp?t=SmartNode.
You will need an account with password to download the firmware. Just register to do so. This is free of charge, as well as the software download.
Connect the SmartNode through the network interface ETH 0/0 with your LAN. The SmartNode is configured as DHCP Client. Please check the lease table of your DHCP server to detect the assigned IP address.
Log in through the web interface of the SmartNode:
Username: administrator
No password
On the navigation on the left, use the item "Import/Export" -> "Import Firmware" to transfer the downloaded firmaware to the SmartNode. Afterwards, the SmartNode must be restarted and it will use the new firmware.
2.3. Configuration and Installation of the INI Files
At the end of this article, you can download a zip-file with several configuration templates. Choose the template that fits to your environment.
2.3.1 Configuration of the INI file
Open the chosen configuration template with a text editor, find the following terms and replace them with the appropriate settings. Note: A term may occur several times in the configuration template and must be replaced accordingly.
STANDALONE:
IP-PBXSERVER IP Address of your SwyxWare server
SIP-NAME SIP-User-ID / Username of your trunk
SIP-PASSWORD Password of your trunk
SIP-REALM Standard realm for SIP clients
MASTER-STANDBY
IP-PBXSERVER-MASTER IP Address of your Master SwyxWare server
IP-PBXSERVER-STANDBY IP Address of your Standby SwyxWare server
SIP-NAME SIP-User-ID / Username of your trunk
SIP-PASSWORD Password of your trunk
SIP-REALM Standard realm for SIP clients
SPECIAL SETTINGS
REMOTE-PATTON IP address of a remote SmartNode
LYNC-SERVER IP address of a Lync Mediation Server
Save the changes after adjusting the configuration file.
2.3.2 Installation of the INI file
Connect the SmartNode through the network interface ETH 0/0 with your LAN. The SmartNode is configured as DHCP Client. Please check the lease table of your DHCP server to detect the assigned IP address.
If you want to run the SmartNode with a manually assigned IP address, please replace the line "ipaddress dhcp" by "ipaddress IP-ADDRESS SUBNETMASK"
i.e. "ipaddress 192.168.172.12 255.255.255.0" for the WAN interface in the configuration file. Additionally, you have to remove the '#' and adjust accordingly:
DNS-SERVER-IP1 IP address of the primary DNS server
DNS-SERVER-IP2 IP-Adresse of the secondary DNS server
STANDARD-GATEWAY-IP IP-Adresse of the default router
Log in through the web interface of the SmartNode:
Username: administrator
No password
On the navigation on the left, use the item "Import/Export" -> "Import Configuration" to transfer the adjusted configuration file to the SmartNode. Afterwards, SmartNode must be restarted in order to get the loaded config applied. The SmartNode will then register with the SwyxWare.
Links
SmartNode Templates
SmartNode Templates with Microsoft Lync profile
The third-party contact information included in this article is provided to help you set up a Swyx IPPBX with a Patton SmartNode PSTN gateway. The information is subject to change without notice. Patton in no way guarantees the accuracy of this third-party information nor is responsible for it's content.
| 
(8748 vote(s))
Helpful
Not helpful