Knowledgebase : Network Access > Remote Access Server
Go into the GUI. Click on the "Interfaces" tab on the left hand side.
Then you will want to click on the first "Details..." tab and there
you will see the MAC address listed as the "Physical Address:".
For Windows 2003 (server) drivers for the 2977 are included in the OS
driver database.
If you are having users that are having troubles connecting to
your RAS server with code version 3.5.1 please be sure to set the TX
level on your RAS box to 14. You can do this by doing the following.
Click DIAL IN -> Modify Defaults -> Scroll to bott...
Yes. See our SNMP Advisory Tech Note at
http://patton.com/technotes/Patton-Security-Advisory.pdf
[http://patton.com/technotes/Patton-Security-Advisory.pdf]
The OID to kill a call is as follows:
1.3.6.1.4.1.1768.5.100.1.3.x
where x=call ID number on the dial-in page of the RAS
This OID needs to be set to 10.
This is valid for both the 2800, 29xx and 3120 series.
The 29xx, 2800 and 3120 models do not support the concept of time/date
like a calendar. The only time it knows is the time since the remote
access server was last rebooted.
In the system log, the time stamping increments by 100 every second.
So dividing...
A Pentium 333Mhz processor or higher.
256 MB RAM for Windows 2000
2MB RAM per 2977 port
Pentium 333 Mhz processor or higher
256 MB RAM for Windows 2000
2MB RAM per 2977 port
The MFR2 line settings are specific to a bit oriented signal on an E1
line. E1 lines are used everywhere in the world but Canada, Japan,
parts of Taiwan, and the USA. The line you will have installed will be
a T1 (message oriented or robbed bit) line.
The US uses a T1 (MESSAGE ORIENTED or ROBBED BIT) line. A MESSAGE
ORIENTED line is a PRI (Primary RateInterface) ISDN line with 23B
channels and 1 D channel. Instead of the phone company sending the
ring voltage in-band with the data, the digital packet ...
There are two (2) passwords. The first is a monitor password which
allows one to view, but not change, all configuration options and
statistical data---all passwords are hidden. The second is a superuser
password which allows full configuration and passw...
New software images can be found at
http://www.patton.com/support/upgrades/index.asp?um=2960
[http://www.patton.com/support/upgrades/index.asp?um=2960]. The
software is upgraded using FTP from any computer. The steps are as
follows.
* FTP into the 29...
The DSP's are best thought of as a resource pool. At ring time the
2960 is told by the calling switch whether the call is digital or
analog. At that time a DSP is allocated and assigned to that call. The
way the DSP's are kept in the resource pool and all...
On the web management pages there is an option to change monitor
privileges. The default is readonly(2). If this is changed to none(0),
the monitor user can not log in to the web pages.
To connect to the RS232 port you need a straight through cable and a
RJ48C to DB-9 converter. These were included with your remote access
server but if you have lost them, the pin-out for the converter is as
follows:
RJ45 DB9
1 - 6 Data Set Ready
2 -...
The 2960 series supports the following types of connections:
ASCII/VT100
Async PPP
Sync PPP
Frame Relay
ISDN
The 2960 supports all of the types of dial-in connections
simultaneously. If the incoming E1/T1 supports ISDN then some users
can connect usi...
On the Patton you need to do the following:
* Go to System Log->Modify.
* Set IP address for Syslog Daemon to the IP address of the machine
running syslogd. Select Submit Query
* Set minimum priority for syslog daemon to the desired level of
log...
Following is an example config for the number of active calls. Our
SNMP MIB definition is contained in links on the SNMP page. The
definitions include the OIDs necessary for MRTG or other programs that
use OIDs to get or change MIB variables. This goes a...
Please click to access a scan of the 2960
[http://patton.com/images/tech_support/mib2960.gif] and 2800
[http://patton.com/images/tech_support/mib2800.gif] mib trees. If you
look at the OID for the dial-in page 1.3.6.1.4.1.1768.5.25.0, you can
follow it d...
BOX TEMPERATURE EXAMPLE:
## Temperature for 2996 Site 1.2.3.4
WriteExpires: Yes
Timezone[29xxTemp]: GMT+5
Target[29xxTemp]:1.3.6.1.4.1.1768.20.1.31.0&1.3.6.1.4.1.1768.20.1.31.0:monitor@1.2.3.4
Title[29xxTemp]: 1.2.3.4 Box Temperature
PageTop[29xxTemp...
The remote access server has a default MTU of 1524. This is the
maximum The MTU of the ethernet media. We recommend that this not be
changed.
The MTU will be negotiated during LCP negotation for a dial-in user.
During LCP negotiation we will tell the rem...
Console into the unit via the RS-232 port Reboot the RAS.
When prompted type bbb >
From the prompt Model29xx/31xx> 'type' factory >
From the prompt Model29xx/31xx> 'type' reset
This procedure will set the unit back to factory defaults. We no
longer r...
Model 29xx Software Installation Procedures:
REQUIREMENTS:
The following must be true of your 29xx before loading new operational
software:
1. You must have a IP address assigned to the 29xx
2. You must have an FTP client on a machine which can commun...
To download the most current AT command list, please click here
[http://patton.com/files/support/2977_AT_Commands.pdf].
Help Desk Software by Kayako