RSS Feed
Knowledgebase : Unified Communications > SmartNode > SmartWare
SN46X8 SmartWare SWR 6.X Sample configuration SmartNode connected as trunk gateway between a SIP network and PBX with 4 S0 port. Copy and paste the below config in to a text editor. Replace all the values as described on the lines starting with a # T...
ENFORCE THE TRANSPARENT CODEC FOR ISDN UD-64 CALLS: Incoming ISDN calls will be split into two call-router paths to enforce transparent codec for ISDN unrestricted digital calls. Note that the VOIP-DATA interface has no route into the call-router, it o...
The DHCP client options, supported in SmartWare are: DHCP Option Name Description 1 Subnet Mask Specifies the clients subnet mask 3 Router Specifies a list of routers for the clients subnet 6 Domain Name Se...
SN46XX SIP to ISDN Trunk Gateway configuration without SIP registration. The ISDN PSTN may be connected to Port BRI 0/0 to 0/X. Copy the content below this introduction and save it to a text file for future upload to the SmartNode. #---------------------...
Firmware file for use in redboot mode. NOT for SN45x2
The reason why the ACK for the 200 Ok from the SmartNode in some cases is not accepted, is due to an invalid branch ID in the via header. Based on the description in RFC 3261, the branch ID for a 2xx response has to be different than in the former messag...
There are two possibilities: 1. Set the ISDN Presentation Indicator (PI) to restricted: 172.16.40.125(ctx-cs)[switch]#mapping-table pi to pi MT-PI-TEST 172.16.40.125(map-tab)[MT-PI-T~]#map default to restricted 2. Delete the Calling-Party Nummer usin...
ISDN LAYER 1 STATES ISDN-PORT NETWORK MODE (NT1): State G1 = NT1 DEACTIVATED State G2 = NT1 PENDING ACTIVATION State G3 = NT1 ACTIVATED AND WORKING State G4 = DEACTIVATION REQUEST RECEIVED ISDN-PORT USER MODE (TE) State F1 = TE INACTIVE, NO POW...
The dial tone generated by a PSTN connection or a PBX can be extended over the Internet or an Intranet by using a pair of Smartnode 452x units or a Smartnode 452x and a Smartlink 402x unit. This FAQ describes how to perform dial tone extension using a Sma...
Call-Routing tables offer two possibilities to terminate overlap dialed numbers. 1. A dialling timeout 2. A special termination caracter like # or * The timout and the caracter can be configured as follows: 172.16.40.125>enable 172.16.40.125#configu...
On the SmartNodes (SN-DTA/4V, 4110, 4120/4V, 4520, 463X, 465X 4830, 491X, 492X, 493X, IC-4FXS) is not possible to use two low-bit-rate codecs at the same time per device. Thus you must choose to use either G.723 or G.729 system wide. G.711 is always suppo...
CODEC NET BANDWIDTH PER CALL (KBPS) USED BANDWIDTH PER CALL (KBPS) MIN. COMPRESSION DELAY (MS) USAGE G.711 a-law 64 96 10 Uncompressed, best voice quality, European audio-digitizing G.711 u-law 64 96 10 Uncompressed, best voice quality, Am...
When using H.323 FastConnect (which is usually the case) together with overlap dialing the voice codec is sometimes not known to the B-side SmartNode in the route lookup. The configuration fragment below exemplifies how to configure a SmartNode such that ...
The selection of a specific codec is somewhat tricky with the H.323 protocol. In SmartWare a specific codec can be entered at 2 different locations: a. in the h323 gateway configuration b. in the h323 interface configurationThe following example exemplifi...
THIS FAQ SHOWS A BASIC DESCRIPTION ON HOW TO CONFIGURE A SMARTNODE COMMUNICATING WITH A SNMP-SERVER. FOR THOSE WHO ALREADY KNOW HOW TO CONFIGURE THE SMARTNODE, PLEASE REFER TO CHAPTER 2 CONTAINING THE MOST USED OID AND AS WELL TEMPLATES FOR CACTI. * CH...
Debugging QoS is different from any other debug commands. It is a two step process. You must be in configuration mode. 1) Go into your service policy and specify "debug queue statistics detail 7" 2) Then do a show command: "show service-policy interface...
Debugging VPNs and ACLs is a bit different than using the other debug commands. It is a two step process to enable ACL debugging. You must first be in configuration mode. 1) Go into "context ip" and then into the ethernet interface and type the following...
Multifrequency Compelled (MFC) Signaling was originally introduced by the European Telecommunication Standards Institute (ETSI). Later, it has been defined by the International Telecommunication Union (ITU) as Signaling System R2 in the standards Q.400 - ...
The profile Argentina may be used when the carrier is Telefonica at Colombia, here is an example to do it by telnet: SN>enable SN(cfg)#configure SN(cfg)#profile r2 default SN(pf-r2)[default]#load argentina
1. Open a telnet session using the command line interface of Windows. Command: telnet "SN-ip-address|SN-hostname". 2. After opening the tool, open the properties of telnet and check the quick edit mode check box. Then change to layout tab and set the he...
Hold down the reset button while you power cycle the unit and make sure you hold it down for at least 10 seconds. Connect a PC to the WAN port of the SN4554. You will have to set your PC statically to an IP address on the same subnet (172.16.40.2 255.255....
The following could be the issue in case a configured tone in a call progress tone profile is not played as it is set. In total 13 different tones, a combination of frequency and volume, can be stored in the SmartNode tone database. This includes as well...
The internal timer configuration command is only able to execute commands that produce an immediate result. Some commands that execute asynchronously cannot be executed by the timer. The following commands (among others) cannot be executed by the timer: ...
DAYLIGHT SAVINGS ON SMARTNODE * On the SmartNode [http://patton.com/twiki/bin/view/Main/SmartNode] a timezone and a DST rule can be defined. For Daylight Saving Purposes there can be Timers defined which adjust the Timezone Offset according to the Day...
The WAN access speed is expected to be large enough to handle all voice connections on the SmartNode. Moreover the voice portion of the used access bandwidth is expected to be small with respect to total bandwidth. For example a DSL access with 700kbps or...
In ISDN supplementary service can be invoked by means of thekeypad protocol. A service can be invoked with the digitsequence *21#. The phone sends these digits as information element 'Keypad Facility' and not as informationelement 'called party number'. A...
Yes. Generally, DTMF can always be transported either out-of-band or in-band. in-band provides the most accurate timing reproduction of DTMF, but it is not suitable when a compressing codec is used, e.g. G.729 or G.723. In these cases, out-of-band has to...
The SmartNode is a router as per RFC1812/RFC1256 and thus sends "ICMP Router Discovery" messages to the subnet to which it is attached. Some MS Windows versions react to such messages and automatically adjust their routing tables. In order to avoid such u...
Up to 3 different gatekeeper IP addresses can be configured on a SmartNode.If the SmartNode is unregistered from the gatekeeper by means of an URQ message, after sending a UCF message the SmartNode tries (instantaneously) up to 3 times (every 20s) with a...
When using NAPT on a SmartNode there is one global IP interface (with the public IP address) and one local IP interface (with the private IP address). The H.323 gateway must be bound to one of the interfaces since it needs to know on which interface it mu...
CONFIGURATION DESCRIPTION: This example shows which mapping tables are used to get the "clip no screening" working towards the ISDN PSTN network. The call comes in on isdn interface 01 and passes the complex function contatining 3 mapping tables. In t...
CONFIGURATION DESCRIPTION It is possible to store call logs with quality information in the local aaa data sink. To do so, a service aaa is needed where the calls are routed through. Create a profile aaa with the method local. Then create a service aaa ...
CONFIGURATION DESCRIPTION The service 'priority' can automatically free resources if a high priority call needs to be established while no resources are available. The service 'priority' can have multiple ports. You can assign a priority level for each ...
CONFIGURATION DESCRIPTION Allows you to pick up Phone 0 and ring all other 7 ohones at the same time. Then once one of the other 7 phones is answered the call is connected and the other phones cease ringing. COMMAND SEQUENCE TO COPY, EDIT AND PASTE co...
CONFIGURATION DESCRIPTION The call-router 'limiter' service limit offers with a flexible technique to limit the maximum number of concurrent calls. It also limits the call-setup rate within a system. Calls exceeding the defined limits can either be simp...
CONFIGURATION DESCRIPTION COMMAND SEQUENCE TO COPY, EDIT AND PASTE #-----------------------------------------------------------------# # # # SMARTWARE 5.X # # # # ENHANCEMENT for CALL-DETAIL-RECORDS over RADIUS # # # # This config example is an enhanc...
CONFIGURATION DESCRIPTION The SmartNode sends a CDR message if a incoming or outgoing Call-Setup passes the SIP-Interface. You may define and configure a independent CDR-services-element for each call-routing-leg. COMMANDE SEQUENCE TO COPY, EDIT AND PAS...
CONFIGURATION DESCRIPTION Incoming SIP call rings four phones simultaneously. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE #-----------------------------------------------------------------# # # # SMARTWARE 5.X # # # # Incoming SIP call rings 4 Analogu...
CONFIGURATION DESCRIPTION Inbound SIP call hunting across 4 FXS interfaces COMMAND SEQUENCE TO COPY, EDIT AND PASTE #-----------------------------------------------------------------# # # # SMARTWARE 5.X # # # # Inbound SIP call hunting across 4 FXS...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide second-dial-tone service. Once a user connects to a SmartNode FXO port, SmartNode will generate and deliver a second dialtone to the user. The routing-table RT_CDPN decide...
CONFIGURATION DESCRIPTION ENFORCE THE TRANSPARENT CODEC FOR ISDN UD-64 CALLS: Incoming ISDN calls will be split into two call-router paths to enforce transparent codec for ISDN unrestricted digital calls. Note that the VOIP-DATA interface has no rout...
CONFIGURATION DESCRIPTION SmartNode used as gateway between a SIP network and a phone, connected to port 0/1. The Port 0/0 is configured as user and can be used as fallback to a PSTN. Emercency calls will be routed to PSTN instead of VOIP. COMMAND SEQ...
CONFIGURATION DESCRIPTION SN46X8 SMARTWARE 5.X Sample configuration SmartNode connected as trunk gateway between a SIP network and PBX with 4 S0 port. The Port S0 slot 0 port 0 is configured as fallback and sync-port. It is configured in the user mode a...
CONFIGURATION DESCRIPTION The example shows you, how to bundle multiple PPP lines into one, using one subscriber. You may add additional lines in the same way. COMMAND SEQUENCE TO COPY, PASTE AND EDIT context ip router interface IF_MLPPP ipaddres...
CONFIGURATION DESCRIPTION The example shows you how to bundle multiple PPP lines into one, using two subscribers. You may add additional lines and subscribers in the same way. IMPORTANT: Both subscribers needs the same mulitlink settings COMMAND SE...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to operate as a DHCP client by pointing a SmartNode IP-interface to a DHCP server on the directly connected LAN. As a DHCP client, upon power-up the SmartNode can automatically retreiv...
CONFIGURATION DESCRIPTION The command sequence below enables static-IP-addressing by assigning a fixed IP address, netmask, and default gateway address to a SmartNode IP interface. To complete this configuration you will need the following information:...
CONFIGURATION DESCRIPTION Sometimes you need to specify default routes for traffic in specific traffic-classes. SmartNodes have three built-in traffic-classes (expandable in configuration) which are used for Quality-of-Service purposes. For each traff...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to operate as a DHCP server. In networks where the SmartNode is the Internet Gateway Router, this configuration is the best way to provide user devices with Internet access. Once ena...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to support dynamic service via DynDNS (i.e. http://www.dyndns.org). If your IP address changes more often than once every 28 days you should use this Service Dynamic configuration. I...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to support static service via DynDNS (i.e. http://www.dyndns.org). If your IP address changes less often than every 28 days, you should use this Service-Static configuration. If your...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode 4638 as a PSTN gateway in combination with a GFI Faxmaker. This example can be used for other SmartNodes too. The only thing which needs to be adjusted, are the ports ...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode 4112 as a PSTN gateway in combination with a GFI Faxmaker. This example can be used for other SmartNodes too. The only thing which needs to be adjusted, are the po...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN49XX/ISDN for use as a PRI gateway in combination with a Cisco Call Manager. The configuration contains variables in brackets <>. Please Replace the variables incl...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN49XX/ISDN to be used use as a PRI gateway in combination with a Cisco Call Manager. The configuration contains variables in brackets <>. Please Replace the variabl...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN49XX/ISDN to be used as a PRI gateway in combination with two Cisco Call Manager (Primary and secondary). The configuration contains variables in brackets <>. Plea...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN5XXX to be used as a Session Border Controller in combination with two Cisco Call Manager (Primary and secondary). The configuration contains variables in brackets...
CONFIGURATION DESCRIPTION Configuration for SN4112 for use with Avaya Open Office. ============================================ This example includes a basic configuration for the SmartNode SN4112/JS for use as an analog Terminal gateway (ATA for Fax and ...
An ISDN S-Bus can provide up to 8W of 40V DC power. Many ISDN Phones draw their operating power from the ISDN S-Bus. This is usually not the case for PBX systems which are typically local mains powered. Check the technical specifications of your ISDN term...
CONFIGURATION DESCRIPTION In some cases, more FXS, FXO or BRI ports are needed as available on one SmartNode for certain applications. This conifg example shows, how to stack two or more SmartNodes, achieving more channels / ports. The idea is to let ...
The analog facsimile attached to a terminal adapter (which in turn is connected to a S0 interface of the SmartNode) does not send the called party number. Analog faxes wait for a dial tone prior to send the called party number. Despite this the terminal...
If you want route a multicast stream, you need to configure this on the ethernet interfaces. There are two commands, one for the sending interface (to the clients) and the other for the receiving interface (eg. from the WAN). interface IF_IP_WAN ipadd...
SmartWare is the embedded software running on the SmartNodes. SmartWare offers a number of feature options such as QSIG, VPN and IP forwarding. Up to SmartWare release 2.20 feature options had to be paid but where not keyed. Starting with release 3.10 a ...
License Key installation is described in the Software Configuration Guide 3.10 in the Chapter "Basic System Management" section "Managing Feature License Keys". To install the licenses, simply copy the install command and license key ("install license 0...
There are two possible reasons for that. 1. You may be trying to install the wrong key. Make sure the keys you are installing match the serial number of the SmartNode. 2. You may have an early access build of SmartWare release 3.00 or 3.10. Please upgrade...
Some SmartNode 4000 series units have a serial number notation using colons ":" that do not work with the early access builds of Release 3.10. Upgrade first to the commercial version of 3.10 and the install the license keys.
IP forwarding will be disabled. That means you can still access the SmartNode on all IP interfaces but the SmartNode is not routing IP packets between interfaces. Also if you have been using other feature options such as VPN or QSIG these functions will b...
H.323 is a non-well behaving protocol in that it signals transport ports (RTP ports) inband in IP packets. When using NAPT (Network Address and Port Translation) this poses a problem since the ports are used by NAPT for address mapping. Thus H.323 does us...
Yes, If you are on a private network, your firewall or NAT (Network Address Translation) router must be "H.323 aware" or you'll need a SIP proxy if you are using SIP. To help determine if your LAN uses NAT, you can use a web browser and go to the followin...
Usually RTP streams are processed on SmartNode before they reach the ACL (Access Control List). This is due to add as less as possible processing delay to it. But in some scenarios the RTP traffic may be restricted using an ACL. For such cases the followi...
In some cases you may want to create multiple SIP gateways to subscribe to multiple SIP Telephony Services at the same time, or to seperate LAN SIP calls from Global/Internet SIP calls. In order to bind multiple SIP gateways to the same IP interface th...
The only Siemens Qsig Protocol, which is interoperable with the SmartNode products is ISO-QSIG. You must choose as QSIG version ISO-QSIG. All other Siemens Qsig versions show restrictions in the supported supplementary services, such as the caller n...
By default the SmartNode handles hook FLASH events by itself, i.e. a call is held locally, and if it is transferred, it is looped locally as well. If you want to transmit the DTMF towards the far end, you must disable the additional servivces on the fxs...
A common application is to accept calls from a PSTN on an FXO port and then ring a telephone connected to a FXS port. In order to send a FLASH out the FXO port to the PSTN, you must disable all supplementary calling features on the FXS interface. For exam...
SmartWare FLASH Codes -FLASH 0 - keep current, reject incoming -FLASH 1 - drop current, accept incoming -FLASH 2 - hold current, accept incoming To toggle between the active and the held call, press flash-hook, followed by the "2" key. Additional...
If the message OUT OF MEMORY appears, you may do the following 1. Store the current running-config in a separate file 2. copy the config which is linked below, to the startup-config in the SmartNode and reload it. Be sure about the ip addresses. If th...
CONFIGURATION DESCRITIPON Configuration for SN4638 for use with OCS. A more detailed explanation you will find on the following link. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE #----------------------------------------------------------------# # # # ...
If a firmware update fails the SmartNode will enter the bootloader mode. You can access the SmartNode ONLY with ethernet on the last known ip-address. The username is "admin" and the password "inalp". After successful login you can download the new fir...
Each SmartNode is equipped with a bootloader application. If an upgrade fails and no valid firmware is available on the system the SmartNode will start in this bootloader mode. The bootloader will allow you to install a new firmware. Please refer to the ...
We recommed two good TFTP Servers: First the Solar Winds TFTP Server is found on the SmartWare CD. You can also download it from the SolarWinds web site [http://support.solarwinds.net/updates/New-customerFree.cfm]. Use SolarWinds version 3.0.9 or higher. ...
Yes, Release 3.10 adds SIP and a lot of new session router features. The configuration must be converted. An easy to use on-line tool and instructions can be found at Smart Convert [http://patton.com/support/smartconvert]
Quote: DES Key Parity from Phil Harding [http://blogs.wdevs.com/philharding/archive/2005/09/08/10490.aspx] ------------------------- A single DES key is 64 bits (8 bytes) long, however the actual key material used by the DES algorithm amounts to only 56...
Yes, with SmartWare software releases dated 3/1/06 and later. For earlier relases, VoIP calls terminated on the SmartNode route the RTP outside the VPN tunnel. A VPN feature license has to be installed for this feature to work.
The SmartNode does not have a preset limitation of VPN tunnels. The number of VPN tunnels that you are able to create is only limited to the amount of available RAM. In practice the SmartNode will support a minimum of 10 VPN tunnels but also 100 tunnels...
T-Online uses the username in three steps. a) 12 digits connect-number b) 9 to 12 digits T-Online-number (if <12 digits add a hash (#) in front) c) user-suffix is always 0001 folowing by @tonline.de The username is therefore: aaaaaaaaaaaabbbbbbbbbb...
CONFIGURATION DESCRIPTION !Additional license required for Dial-up! This example configuration can be used as a backup solution, in case a specific host in a specific network is not available anymore. In this case an ISDN Dial-up connection will be se...
CONFIGURATION DESCRIPTION The following will take calls in the FXO port, and send it out sip. It will also take calls in SIP and then hunt across all the FXO ports to find a open port This config also contains the USA tonesets, you can change that as ne...
This is a configuration template for an SN-DTA with registration to a SIP Telephony provider. With this config all national and international calls as well as the local calls will be routed to the SIP provider. All emergency and special Service Number...
CONFIGURATION DESCRIPTION Generic Altigen H.323 SOHO Router Config COMMANDE SEQUENCE TO COPY, EDIT AND PASTE cli version 3.00 banner "My Altigen Config" dns-client enabled dns-client cache 30 dns-relay webserver port 80 language en snmp community pu...
CONFIGURATION DESCRIPTION SN4528 R5.X -should also load in any SN452x - ignore errors for missing ports - uncommment lines in SVC-DG-BROADVOICE for ports used) - Replace with telephone number - Replace ‹PASSWORD› with Password - Replace ‹SMARTNO...
CONFIGURATION DESCRIPTION SmartNode used as a PSTN/ISDN and terminal gateway in a Media-Streams e-Phone enviroment. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE #----------------------------------------------------------------# # # # SN1x00 # # R3.10 #...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to operate as an H.323 gateway for registration with a GateKeeper. NOTE: You must replace. . . xxx.xxx.xxx.xxx . . . with your GateKeeper's IP address. COMMANDE SEQUENCE TO COPY,...
CONFIGURATION DESCRIPTION SN46XX SIP to ISDN Trunk Gateway configuration without SIP registration. The ISDN PSTN may be connected to Port BRI 0/0 to 0/X. Copy the content below this introduction and save it to a text file for future upload to the SmartN...
CONFIGURATION DESCRIPTION PSTN trunk gateway for Aserisk IP-PBX application COMMAND SEQUENCE TO COPY, EDIT AND PASTE #----------------------------------------------------------------# # # # Patton SmartNode SN46XX # # SWR5.X # # # # PSTN trunk gatew...
CONFIGURATION DESCRIPTION In case you need to put the SmartNode in front of a firewall you can forward every ip-packet which is not handled by SmartNode to the firewall. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE profile napt dmz-host ...
CONFIGURATION DESCRIPTION The command sequence below will create a NAPT profile and apply it to the SmartNode's global IP Interface. A home office with the following characteristics will typically use Dynamic NAPT configuration: - a single global IP a...
CONFIGURATION DESCRIPTION The command sequence below will create a NAPT profile with port mappings and apply it to the SmartNode's global IP Interface. This configuration allows SmartNode to forward incoming IP connections on specified ports of the glob...
CONFIGURATION DESCRIPTION The command sequence below will create a NAT profile with static address mappings and apply it to an IP interface on the SmartNode. This configuration allows SmartNode to translate IP adresses one-to-one for incoming and outgoi...
CONFIGURATION DESCRIPTION The configuration example below shows how to configure 802.1q Vlan's on a SmartNode Ethernet port.   COMMAND SEQUENCE TO COPY, EDIT AND PASTE context ip  interface IF_IP_VLAN1   ipaddress 10.0.0.1 255.255.255.0  interfa...
CONFIGURATION DESCRIPTION Port and context ip configuration for a PPPoE connection over the SmartNodes G.SHDSL. COMMAND SEQUENCE TO COPY, EDIT AND PASTE context ip router interface IF_WAN ipaddress unnumbered mtu 1492 point-to-point use profil...
CONFIGURATION DESCRIPTION Port and context ip configuration for a ADSL PPPOEOA (POINT TO POINT OVER ETHERNET OVER ATM) link over a SmartNode VoIP-Gateway. This example is for SmartNode models using the ADSL interface which is indicated by "/A" in the p...
CONFIGURATION DESCRIPTION FXS Port configuration. To be used in the US. For Europe usage, just replace "bell" with "etsi". COMMAND SEQUENCE TO COPY, EDIT AND PASTE port fxs 0 0 caller-id format bell use profile fxs us encapsulation cc-fxs bind i...
CONFIGURATION DESCRIPTION FXO Port configuration. To be used in the US. For Europe usage, just replace "bell" with "etsi". COMMAND SEQUENCE TO COPY, EDIT AND PASTE port fxo 0 0 use profile fxo us caller-id format bell encapsulation cc-fxo bind i...
CONFIGURATION DESCRIPTION SN4960 E1 Configuration with DSS1 signaling protocol Sample Configuration; port 0 0 may be connected to a PSTN line port 0 1 may be connected to a ISDN E1 PBX COMMANDE SEQUENCE TO COPY, EDIT AND PASTE system clock-sou...
CONFIGURATION DESCRIPTION Port and context ip configuration for a Frame-Relay connection over a V.35 or X21 serial link. The transmit-data-on-edge setting depends on the remote modem device COMMAND SEQUENCE TO COPY, EDIT AND PASTE context ip inter...
CONFIGURATION DESCRIPTION ISDN T1 port configuration. To be connected to a PBX. COMMAND SEQUENCE TO COPY, EDIT AND PASTE port t1 0 0 clock master encapsulation q921 q921 protocol pp uni-side net encapsulation q931 q931 protocol ni2 uni-side ...
CONFIGURATION DESCRIPTION 2300/2400 T1 Card in Slot 3 0 User-Side DD COMMAND SEQUENCE TO COPY, EDIT AND PASTE configure system clock-source internal exit context cs switch routing-table called-e164 TAB-FROM-SWITCH interface isdn IF-SWITCH rou...
CONFIGURATION DESCRIPTION Port and context ip configuration for a PPP connection over a V.35 or X21 serial link. The transmit-data-on-edge setting depends on the remote modem device. COMMAND SEQUENCE TO COPY, EDIT AND PATE context ip interface IF_...
CONFIGURATION DESCRIPTION A standard PPPoE configuration including authentication. # Replace ‹account› and ‹password› COMMAND SEQUENCE TO COPY, EDIT AND PASTE configure profile napt PF_NAPT_WAN port ethernet 0 0 encapulation pppoe context ip i...
CONFIGURATION DESCRIPTION This configuration checks 2 minutes after boot up for new firmware and if available downloads and istalls it. Furthermore the server will be checked every minute for new firmware. Furthermore SmartNode checks 30 minutes after bo...
CONFIGURATION DESCRIPTION Quality-of-Service needs to be configured carefully. Especially the rate-limit values needs to be exact as this is the base for prioritizing the data/voice traffic. All the values in brackets <> needs to be replaced. Please h...
CONFIGURATION DESCRIPTION The firmware 5.X supports the registrar function what allows SmartNode to accept registration from any kind of SIP-clients (telephones, soft-clients). The example configuration shows how such an so called identity needs to be ...
CONFIGURATION DESCRIPTION This configuration examples may be used in applications, where the gateway has to use the SIP-Username, e.g. root calling number, for registration and outbound authentication but the content of the SIP-From-Header may change; e...
CONFIGURATION DESCRIPTION This configuration shows an example for how to route calls beetwen an ISDN and SIP network including registration on a SIP server using the new SIP gateway configuration architecture within the SWR5.T software version. COMMANDE...
CONFIGURATION DESCRIPTION CONFIGURATION IS BASED ON RETIRED SOFTWARE RELEASE! Below you will find different configuration examples for a SIP-Gateway configurations. The type of the proxy does not matter as the configuration is the same. Please note th...
CONFIGURATION DESCRIPTION A Simple Asterisk Registration into PBX T1 on Port 0 0 # # Replace ‹0.0.0.0› with IP address or dns name of the registrar, e.g. 192.168.1.1 # Replace ‹XXX› with account, e.g., 1234 # Replace ‹YYY› with account password, e.g., mys...
CONFIGURATION DESCRIPTION A Simple Asterisk Registration into PBX E1 on Port 0 0 # # Replace ‹0.0.0.0› with IP address or dns name of the registrar, e.g. 192.168.1.1 # Replace ‹XXX› with account, e.g., 1234 # Replace ‹YYY› with account password, e.g., my...
CONFIGURATION DESCRIPTION Configuration for a Pingtel / sipX PBX -US Dial Tones -SN45xx (firmware 5.X) based -Replace all <>-variables with appropriate values CONFIGURATION TO COPY, EDIT AND PASTE profile call-progress-tone US_Dialtone play 1 0 350 -...
CONFIGURATION DESCRIPTION Smartware version R5.X not older than 2010-07-15 Use these two commands to achieve that the SmartNode automatically performs the daylight saving change. This example is for countries with default offset +01:00 and daylight saving...
CONFIGURATION DESCRIPTION SNTP configuration recomendation for Japan. This configuration uses a combination of one DNS name in Japan and one IP address in Japan. DNS server must work work for DNS to be resolved. SNTP should continue to work if DNS break...
CONFIGURATION DESCRIPTION SNTP configuration recomendation for Mexico. This configuration uses a combination of one DNS name in Mexico and one IP address in USA. DNS server must work work for DNS to be resolved. SNTP should continue to work if DNS breaks ...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below enables SmartNode to provide the standard Norway1 style tone set for dial-tones and call-progress tones. COMMAND...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below enables SmartNode to provide the standard Norway1 style tone set for dial-tones and call-progress tones. COMMAND...
CONFIGURATION DESCRIPTION There are Three distinct tones sets used in Bulgaria. Bulgaria1, Bulgaria2 & Bulgaria3. The command sequence below enables SmartNode to provide the standard Norway1 style tone set for dial-tones and call-progress tones. COMMAND...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Czech Republic style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone CZ_Dialtone play ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard France style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone FR_Dialtone play 5000 440...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Hungary-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone HUN_Dialtone play 5000 4...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Italy-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone IT_Dialtone play 200 425 -...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Mexico style tone set for dial-tones and call-progress tones. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone MX_Dialtone play 1 200 4...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Netherlands style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone NL_Dialtone play 1 2...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard New Zealand-style tone set for dial-tones and call-progress tones COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone NZ_Dialtone play 1 50...
CONFIGURATION DESCRIPTION There are Two distinct tones sets used in Norway. Norway1 and Norway2. The command sequence below enables SmartNode to provide the standard Norway1 style tone set for dial-tones and call-progress tones. COMMANDE SEQUENCE TO COP...
CONFIGURATION DESCRIPTION There are Two distinct tones sets used in Norway. Norway1 and Norway2 The command sequence below enables SmartNode to provide the standard Norway2 style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY,...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Poland-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone POL_Dialtone play 5000 42...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Russia-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone RUS_Dialtone play 5000 42...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Slovenia-style tone set for dial-tones and call-progress tones. COMMANDE SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone SLVN_Dialtone play 700...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard South Africa-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone ZA_Dialtone play 1 ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Spain style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone ES_Dialtone play 1 200 425...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Sri Lanka-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone LK_Dialtone play 5000 ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Sweden-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone SE_DIAL play 1 5000 425...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard UK-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone UK_Dialtone play 1 5000 350 -1...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard USA-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE configure system profile call-progress-tone US_Dialtone...
The command sequence below defines a VPN Tunnel that uses AES-128 to route traffic from Side #1 (192.168.1.0) to Side #2 (192.168.2.0). NOTE: -You must replace ‹X.X.X.X› in the template with the IP address for Side #2. -You must replace ‹MySharedKey...
CONFIGURATION DESCRIPTION The command sequence below defines a VPN Tunnel that uses AES-128 to route traffic from Side #2 (192.168.4.0) to Side #1 (192.168.1.0). NOTE: -You must replace ‹X.X.X.X› in the template with the IP address for Side #2. -You mu...
CONFIGURATION DESCRIPTION The command sequence below defines a VPN Tunnel that uses DES to route traffic from Side #1 (192.168.1.0) to Side #2 (192.168.2.0). NOTE: You must replace X.X.X.X in the template with the IP address for Side #2. NOTE: You mus...
CONFIGURATION DESCRIPTION The command sequence below defines a VPN Tunnel that uses DES to route traffic from Side #2 (192.168.2.0) to Side #1 (192.168.1.0). NOTE: You must replace X.X.X.X in the template with the IP address for Side #1. NOTE: You must ...
In some cases SIP calls are disconnected after 32 seconds. This happens when the SmartNode involved is B side of the connection. Looking at a debug log of such a call, it can be seen that several 200 OK and ACK messages are sent back and forth. This is ...
This article contains a SmartNode voip profile configuration example to be used together with a Hylafax software based on Asterisk. As well a Hylafax /Asterisk configuration recommendation is included. Both the SmartNode and Hylafax settings were successf...
The following configuration can be used to register with a Skype Connect account. #--------------------------------------------------------------- # # # # SN4634/5BIS/UI # # R6.x # # Autor: Thomas Tlapak # # Date: 03.07.2012 # # # # Contact: support@pat...
1     INTRODUCTION  Security is in the today communication systems a key element required to have a stable and reliable IT service. This includes not only data security however also written and mutual communication. Open VoIP networks are attackable us...
CONFIGURATION DESCRIPTION The below SmartNode configuration template will help connect your Cyber-Data IP Paging equipment to Microsoft Lync. COMMAND SEQUENCE TO COPY, EDIT AND PASTE IN THE FOLLOWING LINK configuration example [http://support.patton...
Basically all 4xxx SmartNode models are interoperable with Microsoft Lync. On the following link more details about configurations of both, the Lync server and the SmartNode can be found. Microsoft Lync and SmartNode [http://www.patton.com/voip/appnot...
FXS GATEWAY IN COMBINATION WITH ASTERISK This template can be used to register a fxs gateway with at Asterisk PBX.
To enhance Lync with a legacy PSTN or an analogue terminal a Voice over IP gateway is required. The SmartNode products line, Certified for Lync by Microsoft, is the right choose for such a scenario. A step by step configuration guide to configure the Sm...
If a firmware update fails the SmartNode will enter the u-boot mode. Connect a computer to the console interface and restart the SmartNode. You will see the Prompt "=>". HOW TO FORCE THE SMARTNODE ENTERING THE BOOTLOADER/U-BOOT MODE While connected wit...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the standard Japan-style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE configure system profile call-progress-tone JP_Dialtone...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN411X/FXS to be used as an FXS gateway in combination with a Cisco Call Manager. The configuration contains variables in brackets <>. Please Replace the variables i...
The information in this article applies to:     SWYXWARE 2011 R2     PATTON SMARTNODE (6.T BUILD SERIES 2012-07-18) Within the Swyx Technology Partner Programme (TPP) the Patton SmartNode (6.T Build Series 2012-07-18) was successfully tested against a S...
Low bitrate codecs supported on Smartware are G723 and G729 On some of the SmartNodes, only one low bitrate codec is supported at the time, systemwide. There the following setting is required to make the G729 codec work. system ic voice 0 low-bit...
profile call-progress-tone AIRTEL_LL_DTONE play 1 40 401 -19 375 -23 modulated 50 --> 50 - default modulation
1) Open PuTTY. (download link: http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe [http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe]) 2) Click 'Window' and set 'Lines of scrollback' to '9999999'  3) Enter in IP address of SmartNode and h...
This article describes how to configure a Patton SmartNode with Voxbone International Inbound SIP Trunking service [http://www.voxbone.com/], which provides Telephone numbers (DID) and toll-free numbers in 50+ countries and 4000+ area codes [http://www.vo...
CONFIGURATION DESCRIPTION In cases where an ISP assigns to your SmartNode's WAN interface a public IP address, and provides you as well with multiple public IP addresses within the same subnet, all to be assigned to different hosts/servers within your n...
For Ethernet port redundancy, the SmartNode / SmartWare action script functionality will move the interface binding from one Ethernet port to the other in case a failure on the Master Port appears. For the master port supervision, an additional interface ...
To enable SmartNode to connect using ISAKMP VPN to a Cisco ASA here is a template. The goal of this configuration was to create a secure tunnel ( now only for voice ) via VPN. Topology: - - =VPN= - The network 10.100.1...
To configure a SmartWare SmartNode FXS Gateway within 3CX, please visit the link below.  http://www.3cx.com/blog/voip-howto/patton-fxs-gateway-at/ To configure a Trinity SmartNode FXS Gateway within 3CX, please visit the link below. https://www.patton...
When your SmartNode is connected to a public network, it must be properly configured in order to prevent it from unwanted attacks. First of all make sure an ACL is configured and enabled in the corresponding IP interface. In the ACL make sure that only ...
CONFIGURATION DESCRIPTION This example includes a basic configuration for the SmartNode SN4118/JS to be used as a FXS gateway in combination with two Cisco Call Manager. The configuration contains variables in brackets <>. Please Replace the variables i...
CONFIGURATION DESCRIPTION Port and context ip configuration for a ADSL link over a SmartNode VoIP-Gateway using PPPOA ENCAPSULATION. This example is for SmartNode models using the ADSL interface which is indicated by "/A" in the product SKU. In case ...
Article covers configuration impact on 'service aaa' behaviour in case RADIUS server stops responding to Accounting Requests. Tested against SmartNode 4112 running SmartWare 6.5 and Freeradius server version 2.1.10. Our goal was to pursue a solution in ...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the Austria 420Hz style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone AUT420_Dialtone play 5000...
CONFIGURATION DESCRIPTION The command sequence below enables SmartNode to provide the Austria 450Hz style tone set for dial-tones and call-progress tones. COMMAND SEQUENCE TO COPY, EDIT AND PASTE profile call-progress-tone AUT450_Dialtone play 5000...
Whenever you are experiencing connectivity issue on the e1t1/ethernet a great tool to test if the ports are working fine would be the loopback cable. A loopback cable redirects the output back into itself. This effectively gives the network interface th...
Echo is commonly encountered on PSTN when analog lines are involved in the conversation path. Patton SmartNodes have an integrated echo canceller for that purpose. Because it works adaptively, only the echo that really exists is cancelled. The best place ...
The following article is a comparison of the debugging commands found in the Patton SmartNode VoIP Gateway products. Patton SmartNode's have been running SmartWare since conception but Patton recently developed and released a newer software platform calle...
One of the main reasons for this is that the SmartNode does not allow for any "untrusted" host IP Addresses to pass through whenever the "trust" command is configured in the SIP interface. MANAGING TRUSTED HOSTS: A list of trusted remote peers can be ...
By default, the SmartNode listens for both TCP and UDP traffic. In order for the SmartNode to send SIP signaling using TCP, you will need to configure the following: location-service SER_LYNC match-any-domain identity-group default call outbound ...
To import a SmartNode T1 Gateway xml template into 3CX, you will first need to download the template from here [http://patton.com/files/support/kb/Patton-T1.gw.zip]. Once you download the file and extract the "Patton-T1.gw.xml" from the zip file, you will...
Below are the default RTP port ranges in the Patton SmartNodes and how to configure them per software platform.   SmartNodes running SmartWare: RTP-PORT-RANGE 4864 5375 Configuration: 10.10.50.17>enable 10.10.50.17#configure 10.10.50.17(cfg)#con...
Certain carriers require that the Numbering Plan and Type of Number, sent in the ISDN SETUP message, be National/isdn-telephony (ISDNTelephony e.163,4). Unless configured otherwise, the SmartNode will send this as UNKNOWN/UNKNOWN. SETUP (DSS1 User) [040...
The below screenshots shows how Mitel 3300 needs to be configured. Below is the Smartnode configuration where # Smartnode IP= 10.10.10.10 # Mitel Ip = 10.10.10.11 # SIP Account 8998 context ip router   interface eth0     ipaddress 10.10.10.10 255.255....
Patton SmartNodes have a very complex digit manipulation engine that is highly configurable for most parameters within a call setup.   MAPPING TABLE: * Selects the best matching entry * Sets/Changes the value of the defined Information Element * M...
A common problem when SmartNodes are unable to register with 3CX happens to be caused by the auto-blacklist feature by 3CX. After a number of failed registration attempts to 3CX, a device will be blacklisted automatically, thus preventing registration and...
Patton has created new 8-32 FXS port templates that are available to download and install into your 3CX Phone System.  Just a few simple steps and you will be configuring your SmartNode IPChannelBank devices in no time at all. SUPPORTED PRODUCTS: SN4300...